Seaton Seama

Additional Specs, Equipment and Information:

Beam: 18' 9"
Max Draft: 5'
Displacement: 74,500 lbs.

Total Power: 405
Cruising Speed: 16
Max Speed: 20

• All parts made from molds
• Floors, decks and major bulkheads are composite construction and laminated to hull
• 3 layers of Kevlar in the fwd collision zone
• Vinylester resin used for outer laminations
• Longitudinal and transverse stringer system
• All opening port lights to be Pacific Coast Industries with screens
• All fixed port lights to be of the Garibaldi glue in style of windows
• All superstructure windows to be of the Garibaldi glue in style of windows
• Black Anti-fouling bottom paint
• Boot stripe
• Cap rails - molded
• Corecell cored construction with Cook gel coat
• Exterior doors to be Pacific Coast Industries insulated (or equivalent)
• FRP rudders with Aqualoy 22 Hi-strength stocks
• Full-length stringers and athwartships frames laminated over foam
• Hand-laid fiberglass deck, deckhouse, and flybridge cored with high strength Divinycell foam.
• Hull painted
• Linear polyethylene (LP)/acrylic paint
• Interprotect 2000 barrier coat below waterline
• Hull reinforced for stabilizers
• Hull/deck joint through-bolted every 6”, sealed with 3M 5200, glassed over with 3 layers of fiberglass
• Integrally molded swimstep rubrail guard with 2 inch s/s rub strip
• Keel space filled and sealed across top, except at tanks and sumps
• Molded F.R.P. rub rails capped with solid stainless steel trim rails
• Overhead halogen and LED deck lighting (24vdc) on exterior walk and outside pilothouse
• S/S keel shoe – 10 ft long x 1.5 inches
• Scuppers on side decks, and foredeck
• Shaft Tunnels
• Superstructure painted
• Swim step integral to hull

• 316 grade S/S 2” handrails, 1 ½” stanchions, Welds ground and polished
• 50 amp shore power receptacle with 30 amp adapter in aft cockpit
• Aft cockpit cabinet with stainless sink, extendable hot & cold sprayer, fender storage below, and 110 110 v GFI duplex outlet
• Bulwark doors opening inboard with Seadog style latches and bolts
• Chocks at hull sides and transom (4)
• Deck scuppers set flush with main deck and piped out at bootstripe, integeral FRP pipe to hull
• Large deck scuppers, set ½ inch above deck level (to eliminate dark hull streaking)
• Five 14" heavy duty s/s cleats per side, recessed into bulwarks
• Flush lazarette hatches with hinges, gaskets, locks & gutters with drains
• Folding or Pop Up Cleats on Swim Step
• Fresh Water 316 S/S faucet
• FRP Swim step, with s/s brackets. Molded non skid surface. S/S rub rail
• Flush deck hatch with steps down into lazarette, watertight
• Hinged watertight lazarette hatch with gas shock
• Two Lewmar Ocean series, size 60, opening deck hatches to the owners stateroom
• Hot & cold shower fittings on inside of transom adjacent to door, with quick
• Integrally molded cockpit lockers
• Integrally molded non-skid on decks
• Integrally molded seats
• Mooring cleat for dinghy
• Non-spill fuel fills in bulkwark port and stbd
• Overhead low voltage lighting.
• S/S overhead lights, two per side.
• Salon door
• Salt water 316 S/S faucet
• Shore inlets for 220v, 50A AC, Telephone, TV.
• Six 14” heavy duty s/s cleats secured to plates inside bulwarks
• Two inch S/S swim step staples
• Side gates to have robust hinge and latch assemblies P&S
• Water fill in aft cockpit

• 1,500 lb capacity Steelhead davit with powered luffing, hoisting and rotation
• 24 V dc chrome dual trumpet Kalenberg air horn
• 275’ 3/8” HT galvanized chain, 200’ 5/8” anchor rode
• 316 grade S/S 2” handrails, 1 ½” stanchions, welds ground and polished
• Aluminum plate laminated inside deck for tender tie down
• Anchor – 80 lbs CQR
• Deck drains plumbed to boot-stripe
• Dinghy chocks
• Foredeck includes storage locker, fresh water bib and 110 GFI outlet.
• Four 14” heavy duty S/S cleats
• Four S/S chocks
• Fresh Water 316 S/S faucet
• GFCI 110v AC outlet
• Integrally molded non-skid on deck
• Lewmar Ocean series, size 60, opening deck hatch over forward stateroom
• Maxwell VWC 3500 lb vertical windlass with up/down switch at bow and pilothouse
• Molded anchor shelf for stainless steel frame and bow roller
• Propane storage locker.
• Seawater wash down on foredeck
• Storage lockers

• Bitter end fittings for anchor rods
• Forepeak drains directly overboard.
• FRP Chain and rope lockers with removable s/s access plates and s/s chain
• Hatch scuppers
• High gloss poly paint finish, interior of chain locker
• Overhead lights in chain locker
• Pipes & rollers for anchor gear
• Anchor pockets P&S polished S/S
• Watertight collision bulkhead

• AC source light
• Air horn with twin trumpets
• Aquasignal navigation lights, series 42, in accordance with appropriate Collision regulations
• BCS powered hydraulic steering with destroyer-type wheel
• Electronics console
• Engine instrumentation
• Fire system repeater alarm
• Flybridge cushions on settees and helmseat using EZ dri foam with Sunbrella fabric
• Helmseat for two persons at raised control station
• Lexan venturi with s/s rail
• Settee, with stowage under, watertight access hatches in seat
• Main engine sea water flow alarms
• Perfix snaps for attaching cushions
• Ritchie compass with light & dimmer
• Rudder angle indicator with light and dimmer
• 316 grade S/S 2” handrails, 1 ½” stanchion, Welds ground and polished
• S/S signal mast with bow and anchor lights and aft facing floodlight
• Starter engaged warning lights
• Steering console with engine controls
• Table stbd side with fixed granite (or Corian) top
• Two Mastervolt 24v to 12v DC-DC converters with 12v battery back-up system.
• Upholstery and mesh backs for drainage
• Integrally molded non-skid on deck

• 100 USG fresh water tanks w/sight gauges
• Aft & main DC electrical panels
• Aft shorepower inlet circuit breakers
• Air-conditioning compressors
• Battery master switch panel
• Bow thruster Main Switch panel and fuse
• Deck and hatch scuppers
• Fresh water pumps, inlet filter and pressure regulator
• Groco raw water strainers for A/C
• Hi bilge alarm
• Hull finished with gloss white polyurethane paint
• Hydraulic power pack on anti-vibration mounts with FRP drip tray
• Overhead lights S/S
• Starboard platforms and sole boards with S/S lifters
• Steering gear.
• Submersible bilge pump
• Variable frequency drives for 3-phase salon & pilothouse air-conditioning

• 34” x 30” 4-Blade, class 1 propeller
• Aquamet 22 prop-shaft
• PYI dripless shaft seal
• Shaft to be 3”, shaft tube and shaft seal to accommodate 3” shaft
• Shaft zinc and bonded transom underbody zincs
• S/S rudder support bolted on to FRP hull skeg

• Bow and stern flag staffs
• Hawes holes and cleats of stainless steel: (4) bow, (2) amidships and (2) at stern
• Non-skid molded decks
• Stainless steel capped rub rails
• Seama 60 name plates mounted on aft exterior side salon bulkhead, S/S
• All exterior hardware to be type 316 S/S

• 110v GFI electrical outlets
• 21.5Kw Northern Lights genset with soundshield and combined muffler/water
• 220 A/H port engine/genset starting battery bank
• 220 A/H stbd engine/genset starting battery bank
• 305-1 ZF Transmission 2.5:1
• 50 amp Glendinning shore power system with 50' cord reel
• 8” Lift muffler with bypass and underwater exhaust; insulated blanket in dry portion of system
• 900 A/H house battery bank consisting of 12 Lifeline GPL 6CT AGM (6 volt) batteries
• AC and 24v DC lighting
• All hoses double clamped below waterline
• Anti-vibration soft mounts for genset
• Aquadrives with thrust plate, CV joints and soft engine mounts
• Automatic back-flush module
• Ball-type seacocks on all thru-hulls at or below waterline
• Bilges painted with glossy white poly paint
• Bronze thru-hull fittings with bronze seacocks
• Charles Isolation transformers (2)
• Control panels with VDO tacho & start/stop buttons for each engines
• Cutlass-type shaft bearings
• Delta-T air intake baffles with auto-close in event of fire and guarded manual switch in cockpit
• Drip pan under engine
• Dual sea chest with central shut off valve and strainer
• Emergency bilge pump using a Y-value off the engine intake
• Engine access hatch
• Engine room heat extraction blowers (2)
• Engine room Sounddown system on the bulkheads, hull sides and overhead
• Equipment platforms
• Fire retardant FRP fuel tanks (4). With sight gauges
• Fire suppression system with auto engines/genset/blowers shutdown
• Fresh Water fill hose for engines
• FRP drip pans underneath main engines
• Fuel Polishing System
• Fuel transfer system with pump & flow meter
• Full-length stringers and athwartships frames laminated over foam
• Groco raw water strainers for engines gensets A/C and all seawater intakes
• Heat detectors (2)
• Heavy duty air-horn compressor
• Sound insulation covered with perforated aluminum
• Hi-bilge alarm
• 50’ shore cord
• Kabola heating system. (8 Hot water radiator heating units)
• Lead foam sound insulation
• Lube Oil Changing System - Reverso
• Lube oil pumps (2) for engines, transmissions and generator
• Main engine exhaust system with water-lock muffler
• Mastervolt soft-starts (2)
• Sole lifters S/S
• Hydraulic Stabilizers
• S/S safety rail around engines
• Submersible bilge pump
• Twin Cummins QSL9 405 hp electronic engine with 24 V 80 amp alternator
• Underwater exhaust and internal water-lock muffler system
• Village Marine water maker or equal, 600 gpd

• Conrad 8’ antenna with mount
• Icom M-504 VHF with 25 watt hailer and intercom
• Nobeltec navigation suite, computer, 19” Sony display, wireless mouse and keyboard, WAAS GPS.
• Simrad AP 25 Autopilot with hydraulic pump set
• Simrad IS-12 instrument system with combination depth/speed/temp and wind functions
• Simrad Radar / Chart plotter with WAAS GPS 10” LCD display and 24” dome

• 4 FRP fuel tanks made of vinylester and fire retardant resins
• Computank Fuel & Water tank level indication system, using pressure type senders
• Digital fuel flow meter for transfer system
• Electric fuel priming pumps for main engines
• Fuel filters. Racor 75/1000MAX Duplex with vacuum gauges for main engines.
• Fuel lines to be USCG approved and can be used with bio fuels
• Fuel management panel for engine/genset supply return selection
• Fuel manifold on day tank
• Fuel tank float switches and Hi-level alarm
• Fuel tank sumps and drains with shut-off valves on all tanks
• High capacity 24v DC Fuel Transfer pump with suction & delivery manifolds
• Primary fuel filters with water-in-fuel sensors for main engines
• Racor 500MA fuel filter for generator
• Sight glasses on all fuel tanks with self-closing safety valves
• Vents are located above the main deck

• 40 USG Torrid water heater with two 220v AC heating elements and two heat
• Back up X-Caliber 24v DC Headhunter Fresh water pump
• Deck fill and vents
• exchanger coils, drain & pressure release valves.
• Fresh Water 316 S/S faucet in cockpit
• Fresh Water 316 S/S faucet on flybridge
• Fresh Water 316 S/S faucet on foredeck
• Fresh water coil hose in engine room
• Grohe interior faucets
• Hot water Re-circulation solenoid valve and timer with switches in both heads
• Mach 5 110v AC Headhunter fresh water pump
• Sea tech plumbing hoses
• Sight glasses on water tanks
• Stainless Steel (2) ?00 gal water tanks (total ?00 gals)
• Whale gulper shower sump pumps
• Whale plumbing system

• Groco intake strainers for main engines, generator and sea water system
• Salt water 316 S/S faucet in cockpit
• Salt water 316 S/S faucet on foredeck
• Sea water flush line connected to black water tank, with self closing safety valve
• Whale brand plumbing
• X-Caliber 24v DC Headhunter seawater pump and strainer

• Rule electric bilge pumps with auto/man control
• Engine driven bilge pump system
• Engine room bilge sump pump – Whale Gulper
• Forward bilge sump pump – Whale Gulper
• Hi-level bilge alarm switches in lazarette, engine room, and forward bilge
• Manual bilge pump for all bilge compartments and engine room

• All sanitary hose of high quality sanitation Sealand
• Black water tank of FRP (?00 gal)
• Gray water tank of FRP (?00 gal) with Whale pump
• Sealand T-24 or equivalent macerator pump/discharge pump with deck discharge fitting and Y-valve

• Xxx gal Black water tank
• Anti-odor filters on holding tank vents Port & Starboard
• Back up 24v DC Sealand macerator pump
• Black water tank seawater flushing system, with self closing safety valve
• Black water tank suction deck fittings port and stbd side
• Groco intake strainers for main engines, generator and sea water system
• Headhunter 110v AC black water discharge pump
• ITIM Tank monitoring / pump control system
• Plastic lined pressure accumulator tank
• Sea water flush line connected to black water tank, with self closing safety valve
• Toilet flushing for both Seawater and Freshwater.
• Toilets flush to FRP holding tank with level indicator or directly overboard

• Bow Thruster 30 hp Hydraulic
• Electronic engine controls
• Hydraulic Kobelt steering system
• Back lit rudder angle indicators at pilothouse and flybridge stations
• Electro/hydraulic steering system
• Destroyer wheel at flybridge and in pilothouse
• FRP rudders with Aqualoy 22 stocks

• AC
• 21.5Kw Northern Lights generator, 220v single phase, in sound shield mounted on
• AC Contactor Box
• AC outlets throughout boat.
• GFI type in heads, galley, engine room and exterior locations
• Anti-vibration soft mounts
• Charles Isolation transformers (2)
• Digital meters (volts, amps, watts and frequency) and circuit breakers as required
• Four 220v, 50 amp shore inlets fore and aft connected so as two can be used together
• Imtra light switches and dimmers.
• Integral inverter bypass system
• Inverter remote control panel in pilothouse.
• Load distribution panel. Split panel system. Sub panels as required
• Mastervolt soft starts (2) simultaneously
• Tinned copper wire used throughout
• Two 3,500 watt stacked pure sine wave Outback inverters
• DC
• 110 amp Leece-Neville alternators on each engine with Balmar multi-stage external regulator
• 12v DC via two 24v-12v DC-DC converters & back-up battery system located on flybridge
• 140 amp Balmar auxiliary alternators on each engine with Balmar multi-stage external regulator
• 900 A/H house battery bank consisting of 12 pcs Lifeline GPL 6CT AGM (6 volt) batteries
• Advisory indicators for key pumps and engine room lights
• Alarm panel for engine functions, bilge, fire, sea-water flow etc
• Battery disconnect and selector switches accessible from outside engine room
• DC load distribution center with breakers.
• Link 10 digital battery monitor
• Main ships system 24v DC
• Mastervolt 15 amp battery charger for engine/genset starting batteries (24v)
• S/S Aquasignal navigation and anchor lights
• Three isolated battery banks
• Tinned copper wire used throughout
• Electrical Systems Bonding:Copper strap or cable connecting all thru-hulls, underwater fittings, pulpit and
• Copper strapping system in engine room, flybridge and pilothouse for SSB radio
• Counterpoise
• Flybridge rails – (equipotential bonding system)
• Zincs on transom (2)

• Individual fresh water wash on forward-facing windows
• (3) 110v Electrical duplex outlets with a 12vdc outlet on console
• AC/DC electronics panel hinged for easy access
• Air reservoirs for Buell air horn (2)
• Air-conditioning with ability to run on inverters whilst main engines are running
• Alarm and advisory panel
• Back lit electrical distribution panels for AC and DC
• Back lit engine start & stop/Ignition buttons
• Hydraulic steering with Destroyer type steering wheel, 32”
• Bilge and sump pump control on advisory panel
• Chart light on flexible arm
• Chart table with double-guide drawers and stops
• CO detector
• Control for bow thruster
• Demister blower on forward facing windows
• Dimmer for instrument lighting
• Dismountable control console with space for owner supplied electronics
• Door stops and holders.
• Doors on AC, DC and advisory panels
• Electronic engine controls. Glendinning EEC 3 with back up gear and throttle with
• Engine display screens on lower console
• Engine power key-switches on advisory panel
• Equipment running advisory panel
• File drawer
• Fire system and high level bilge alarms panel
• FRP sandwich with Nidacore honeycomb composite sole
• Generator digital control panel
• Helm chair
• Hinged soffit access to underside of flybridge console
• Horn control
• ITIM Black water tank level indication and pump control panel
• Main engine sea water flow alarms
• Overhead electronics console
• Overhead electronics panel
• Overhead halogen lights with red lights above dash
• Pilothouse windows to be tempered and/or safety glass
• Pre-wired for intercom/phone system
• Reading lights behind settee
• Remote Start/Stop Switch: Main engine & Generator remote start/stop switches in pilot house.
• Ritchie Compass with light & dimmer
• Rudder angle indicator with light & dimmer
• Self-parking, heavy-duty windscreen wipers with multi-speed/intermittent controls
• Starter engaged warning lights
• Storage area under settee and chart drawer
• Synchronizer and troll
• Windlass up/down switch & control circuit breaker
• Wiring routes to facilitate equipment installation

• 110v electrical GFI outlets duplex
• 20.5 cu ft side by side refrigerator/freezer
• Air-conditioning
• Broan trash compactor
• Cabinets
• Convection microwave oven
• Dishlocker at stbd side with opening top & front
• Drawers with guides and stops
• Duplex 110v AC ground fault outlets
• FRP sandwich with Nidacore honeycomb composite sole
• Grohe swivel faucet with removable spray head
• Insinkerator waste disposal
• Instahot
• Kenyon 4 burner flush cooktop with s/s potholders
• Overhead and cabinet lighting to be 24vdc Halogen or LED
• Overhead cabinets
• Pull out pantry for can storage
• Sharp microwave convection oven with hood, light and exhaust fan
• Slide-out pot/appliance storage lockers (2)
• Solid surface counter tops with backsplash and outer edge to match cabinet design
• Stainlass steel sink
• Xantrex propane control with gas alarm
• Y Valve: "Y" valve and bonded through-hull for overboard discharge of gray water from the sink.

• 110v electrical duplex outlets and a 12V outlet.
• Access hatch to allow for engine removal
• Air-conditioning
• Bose DVD/CD/AM/FM player, 2 speakers and subwoofer
• Built-in settee with storage under (port side) with starboard side seating
• Carpeting
• CO detector
• Door stops and holders.
• Entertainment cabinet with Sharp Aquos or equal 26” flat screen
• Fixed windows in house sides
• FRP sandwich with Nidacore honeycomb composite sole
• Granite (or Corian) counter tops
• LED and/or halogen overhead lights
• Medium grey tinted, tempered, glass.
• Overhead light fixtures on dimmers
• Overhead valence with room to accommodate shades and blinds
• Pre-wired for intercom/phone system
• Soundown carpet pad
• Teak joinery with satin varnish hand-rubbed finish
• Teak valance over windows with LED rope lighting
• Wall mounted sconce style lights
• Window treatments
• Wood window blinds
• Yacht table

• 110 V outlets
• Berth reading lights.
• Beveled-edge mirrors
• Bulkheads with teak to waist height with Ultrasuede above
• Cedar lined hanging lockers, port and starboard.
• CO detector
• Door stops and holders.
• Doors teak frame with flat teak panels and curved top
• Drapes
• Drawers with center guides and stops
• Foam mattress
• Two fixed S/S portlights
• Two opening S/S portlights
• FRP sandwich with Nidacore honeycomb composite sole
• Hanging lockers. Teak faced with louvered doors. Automatic interior lights
• LED Rope lighting under bed and steps
• Low voltage Xenon overhead lights on dimmers.
• Pioneer car stereo with speakers
• Queen berth with 8” mattress and drawer storage below
• Sump and condensate pump for air-conditioning
• TV space on bulkhead
• Upholstered Headboard
• Vanity
• 110v GFI electrical duplex outlet
• Beveled-edge mirrors
• Bi-fold shower door
• CO detector
• Door stops and holders.
• Drapes
• Exhaust fan
• FRP sandwich with Nidacore honeycomb composite sole
• FRP/PU coated shower stall with granite sole and auto sump pump
• Granite counter top with porcelain basin
• Grohe faucets and accessories
• Grohe shower mixer, pressure and temperature compensated
• Headhunter pressure-jet toilet
• LED and/or halogen overhead lights
• Low voltage Xenon lighting
• Mirror
• One opening S/S portlight
• S/S Toiletries rack in shower
• S/S Towel rails.
• Solid surface counter top
• Ventilator fan

• 110 V duplex outlet
• Berth reading lights.
• Beveled-edge mirrors
• Bulkheads with teak to waist height with Ultrasuede above
• CO detector
• Door stops and holders.
• Doors teak frame with flat teak panels and curved top
• Two fixed S/S portlights
• Two opening S/S portlights
• Drapes
• Drawers with center guides and stops
• Foam mattress
• FRP sandwich with Nidacore honeycomb composite sole
• Hanging locker, end table and drawers
• Hanging lockers. Teak faced with louvered doors. Automatic interior lights
• LED and/or halogen lighting
• LED Rope lighting under bed and steps
• Low voltage Xenon overhead lights on dimmers.
• Over/under bunks with 6” mattress
• Queen-sized bed with hydraulic lift and manually slide
• Reading lamps beside berth
• Storage under berth
• Sump and condensate pump for air-conditioning
• TV space on bulkhead
• Upholstered Headboard
• Vanity

• 110v AC GFI outlet
• 110v GFI electrical duplex outlet
• Beveled-edge mirrors
• Cabinets above and below
• CE-approved Portlight with removable insect screen
• CO detector
• Door stops and holders.
• Drapes
• Exhaust fan
• FRP sandwich with Nidacore honeycomb composite sole
• FRP/PU coated shower stall with, auto sump pump & seat
• Grohe Faucets
• Grohe shower mixer pressure and temperature compensated
• Intake and discharge head vent fans
• LED and/or Halogen lighting
• Lockers
• Low voltage overhead Xenon lighting
• Marble or granite counter top
• Porcelain wash basin in granite counter top
• S/S and glass custom shower door
• S/S Towel rails.
• One opening S/S portlight
• Scanvick shower/sink faucet with hand held mount showerhead with adjustable spray
• Solid surface counter top
• Headhunter pressure-jet toilet
• Ventilator fan

• 110v AC outlets
• Berth reading lights
• Bookshelves
• CO detector
• Door stops and holders.
• Foam mattresses
• FRP sandwich with Nidacore honeycomb composite sole
• Beveled-edge mirror
• Hanging locker with auto lighting and louvered door
• LED Rope lighting and drape tracks at portlight openings.
• LED rope lights under berths
• Low voltage Xenon overhead lighting
• S/S CE-approved portlights with removable insect screens
• Twin berths
• Upholstered Headboards
• Valance over portlights

• Access doors to staterooms
• Bosch washer and vented drier in cabinet behind sliding door
• FRP sandwich with Nidacore honeycomb composite sole
• Lower part of bulkhead teak. Upper part Ultrasuede. Teak chair-rail trim at join
• Overhead low voltage Xenon lighting
• Rope lights at stairs to salon and forward cabin

• All cabins pre-wired for intercom/phone system
• Cabinets to have pre-finished maple interiors for easy cleaning and furniture quality
• Cantalupi brand lighting with 28v Xenon bulbs
• Carpeting - salon, master, and guest staterooms controls
• Courtesy lights on all indoor stairways to be LED type
• Cruisaire reverse cycle A/C throughout using REU model quiet blowers and SMX HT controls
• Dimmer switches in the salon, pilothouse and master stateroom.
• Entertainment speakers pre-wired from salon to master, pilothouse, aft deck, and flybridge
• Flooring - Amtico flooring in pilothouse, galley, and companion / stairways
• FRP sandwich with Nidacore honeycomb composite sole
• Hafele push/pull positive locking latches on interior cabinetry
• Hanging lockers lined with teak
• Headliners of acoustical soft vinyl, Whisper Wall panels
• Insect screens for all opening windows, portlights and skylights
• Interior cabinetry doors use fully adjustable Euro style hinges
• Interior cabinetry drawers use side mount, full extension, ball bearing drawer guides
• Interior hand railings on stairways
• Interior lights to be 24vdc LED, Halogen and/or fluorescent
• Lead foam insulation between accommodation bulkheads
• LED mood rope lighting behind valances, stairs and settees
• Light fixtures to have shiny s/s (chrome) finish
• Mobella interior door locks
• Stackable washer and dryer
• Teak joinery with satin varnish hand-rubbed finish