Norpac Yacht & Ship Brokerage logo
Norpac Yacht & Ship Brokerage
Please enter a valid name!
Please enter a valid email address!
Message cannot be empty!
sending...
Call Now

Toll-free: 877-444-5087
Tel: (510) 232-7200

Norpac Yacht & Ship Brokerage

1150 Brickyard Cove Road Suite B9
Richmond, CA 94801
United States

Visit Website
 

CUSTOM MEGA SLOOP Performance Cruiser, Southern California, CA

US$ 695,000

Click on image to enlarge 
Interested in this boat? Toll-free: 877-444-5087
Tel: (510) 232-7200
Get a Boat History Report
Get a shipping estimate
Zip Code:
Calculate
  • Description
  • View Full Specifications
 
Year:
1996
Length:
100'
Engine/Fuel Type:
Single
Located In:
Southern California, CA
Hull Material:
Composite
YW#:
1741-1992947
Current Price:
US$ 695,000 


THE ULTIMATE AMERICA'S CUP VIEWING PLATFORM!!! and SHE IS FAST @ 26+ Knots!

The Sailing Yacht Christine is an awesome vessel, she would make a very attractive charter yacht or would be an exceptionally gracious pleasure yacht and is now available at a fraction of what it would cost to build her. She presents a rare opportunity to own & operate a truly outstanding vessel and is in fine condition.

THE HULL
The yacht’s hull was fabricated from totally epoxy resin saturated 1/8 inch thick cedar laminates. Each layer was epoxy glued 90 degrees to each other and wrapped around to include the deck, in essence creating a structure that is a continuous and seamless sheet of waterproof plywood. Strategic high load areas near the mast bulkhead and the keel are reinforced with carbon fiber between the laminates. There are 10 layers of veneer besides the 5/16 inch thick tongue and groove mold that is visible throughout the interior, including the extreme bow and stern, as well as every part of the bilge. The interior mold is epoxy saturated and Linear Polyurethane varnished throughout the ship.

All bulkheads are foam filled, laminate sided and finished with varnished epoxy coated tongue and groove cedar veneer.

The keel was fabricated in form of a steel jacket fastened over a welded internal structure that is 11-feet tall. The bottom of it was hot poured with 30,000 pounds of lead, and the upper portion of the keel foil serves as a fuel tank holding 200 gal. of diesel.

The cabin sole is constructed from scarfed and laminated oak beams. Individual panels of 1/2” inch plywood fit in between and are easily removed for instant access to all locations in the bilge.

The foot of the mast terminates in the forward shower. Any rain or green water that penetrates the structure through the halyard or sheave slots of the extrusion is being expelled through the shower sump.

THE GALLEY
Our galley is flanked by a horizontal freezer. Besides assuring fresh food, it is strategically located to keep the chef in the cooking area, when rough seas or heeling could command otherwise. The upright fridge and freezer is made by GE.

LIVING QUARTERS
Below decks are 17 beds... ½ of them are wide enough to sleep 2 people. In addition, there is an owner’s cabin with a large hanging locker, oversize queen bed, bathroom, shower, lots of storage, TV, CD player and surround sound. There are 2 additional bathrooms and a large shower, as well as a very sizable hanging locker and lots of storage space throughout the vessel.

WATER & POWER
Potable water is stored in 4 separate tanks, located under port and starboard bunks. The "Village Marine Tech" water maker is new and powered electrically.

A 250 HP Turbo charged Cummings Diesel Engine with a Borg Warner Transmission provides propulsion under power at 10 kts. The transmission’s output shaft connects to a Morse chain drive unit that terminates 3 ft below into the keel. >From that point, a 2" shaft drives a Martec folding propeller. The shaft is short and roller bearing supported on each end for vibration-free operation. The bearings and chain are lubricated via an oil sump, also in the keel and don’t require any maintenance. Without any sails, just powered by the engine, the yacht cruises 10 kts at 2300 rpm using 7 gal. of fuel per hour, or 5 gal. per hour at 8 kts.

Sailing down-wind without any help from the engine, "Christine" has sailed faster than 26kts.

There are 4 additional fuel tanks located beneath the bunks for a total of 700 gal. fuel capacity.

SAILS AND RIGGING
The mast extends 130 ft. above the water line. It was fabricated from an aluminum extrusion and aircraft riveted the lengths of it. The boom has a fixed clew, and moves away from the mast hydraulically to flatten the sail.

Lidgard Sailmakers in New Zealand made:

(1) 2-ply Mylar full battened mainsail.
(1) Mylar # 1 genoa
(1) 2-ply Mylar # 3 genoa
(1) Mylar 165% reacher
(1) Nylon 110ft. Asymmetric spinnaker
(1) Mylar tallboy
(1) Mylar staysail to go with the reacher

There are also have at least 10 other assorted spinnakers, as well as a blast reacher and other mainsails and genoas purchased from the Japanese A/C boat. Some of these sails were hardly used by the America Cup syndicate and are excellent.

The head sails are stored below the cabin sole. Longitudinal bulkheads are located below the waterline form the compartments. These tunnels are also epoxy coated and varnished, which helps the sausage bagged sails to slide smoothly in and out of their respective locations.

The vessel features 4- Primary Barient grinder drums that are inter connected by 3- pedestals. There are 9-various other winches.

The rod rigging was custom designed by Navtec Engineers.

ELECTRONICS
The electrical needs of the yacht are met by 3 separate banks of deep cycle batteries. One battery bank provides the engine and generator starting power, the second furnishes isolated power supply for the computer and instruments. The third bank services the remaining components and fixtures for the vessel.
A 5000 watt Northern Lights diesel generator services the 110 volt needs of Christine. It also powers the computerized charging system for the battery banks.
While the yacht is in use, the generator runs full time and virtually silent. It has a dual pack of sound insulation and is positioned in the insulated engine room. The generators use 1/2 gallon of fuel per hour, making it an inexpensive source of energy.

Christine has a Data Marine Offshore Electronics Package that is hardwired to a Swiss GPS computer, as well as to the vessel's main computer that is used for the electronic chart system. The computer is a latest high speed Dell unit with a 17" flat NEC high resolution monitor.

All electronics “talk” to each other via NMEA 0183.

MAINTENANCE
At Christine’s last haul, the bottom was sanded wet and dry, and painted the airless method with 3-coats of Z-Spar AB-90". The sides were buffed, polished and waxed.

The 10 deep cycle batteries were replaced this year.

Since launching Christine, nothing has broken with the exception of the carbon fiber spinnaker pole, which was replaced with an aluminum one, and no other changes to the systems and components on this yacht have been necessary. Christine awaits your pleasure and we consider her to be an exceptional value in a world class vessel.





Please contact at (510) 232-7200

Interested in this boat? Toll-free: 877-444-5087
Tel: (510) 232-7200

Other Boats from Norpac Yacht & Ship Brokerage

View all Boats from Norpac Yacht & Ship Brokerage
Email Us
Please enter a valid name!
Please enter a valid email address!
RE: CUSTOM MEGA SLOOP Performance Cruiser, Southern California, CA
Message cannot be empty!
sending...