1953 X-Army “T” boat #504 (The Mi-T-Mo) Fully restored into a trawler with 9x12 salon, 18x18 master stateroom with queen bed, desk, full size closets, full size attached master bath along with extra heavy duty full size washer and dryer. Galley has recently been remodeled to include modern cabinetry and a pantry. Guest quarters include half baths off of salon and half bath off the galley.
Stepping aboard through the midships gate, it is impossible not to know that you’ve stepped onto a real ship. The massive steel construction is everywhere, from bulwarks, to steel ladders and steps, to submarine hatches in the deck, large watertight hatches with dogs, to cleats the size of Michael Jordan’s sneakers welded directly to the steel deck. This is a no-foolin’ workboat, and Mike has not spent a penny to make it otherwise.
After removing all rust and corrosion, Mike and his friends applied Devoe two-part epoxy primer on all interior and exterior steel surfaces. The paint that goes over the epoxy is cosmetic, as the two-part coating is the best way to handle steel in a hostile marine environment. And, as painstaking as that job may be, it only has to happen once. The surface paint gets renewed every three years or so.
It was a blustery day when we visited Mike aboard MI-T-MO, yet she felt as though she were aground, unlike the neighboring boats. 90 tons does make a difference! Mike says that due to the round shape of her hull, she does roll under way in rough seas, but the motion is slow and predictable. He is considering paravanes, but it hasn’t been a pressing need.
Wide and protected side decks run the length of the boat, and the entire exterior remains a platform for continued tug work—so the rough and ready feel of the boat is necessary. Everything is oversized, completely mil-spec in construction, intended for a hard, but long life.
Up forward, there is a 110VDC windlass to handle the two anchors—150-lb. and 200-lb. Danforth anchors on all chain rodes. The use of 110VDC is common on older tugs and workboats, and Mike told us it is preferred for a number of reasons, although he did extensively rewire the boat to handle 32VDC, as well as 110/220VAC for the various onboard electrical equipment.
A large fo’c's’le hatch leads down into the forward stateroom/galley, providing both ventilation as well as easy access between galley and deck. During the season, Mike and Ramona eat up on deck, on a large picnic table that sits on deck, just forward of the pilothouse, under a blue awning rigged for shade over the main cargo-handling boom. The large awning covers an area of deck over what used to be the 17′ by 17′ cargo hold, and is now the master stateroom. Since Mike welded over the cargo hold hatch, they retrieved some wonderfully usable deck space—a mid-size automobile would stow here just fine.
The aft deck is also all business, complete with towing bollard. A watertight hatch opens for access into the lazarette, which might as well be called the basement. Mike hasn’t done much yet to this lazarette, but it is an enormous area sealed off from the rest of the ship. It could be made into additional staterooms, mega storage, or just a big empty watertight compartment.
Mike and his buddies extended the boat deck to provide overhead protection on the side decks and aft deck, and the result looks great, as well as providing good protection from tropical sun and rain. It also creates a huge boat deck. The 13-foot Nautica dinghy seems almost small up there.
There is a ladder up to this boat deck, and Mike installed Morse controls for running the boat from the boat deck, kind of a mini-flybridge. The stack is just a bit higher than the pilothouse roof, and there are dry exhausts for both gensets, one of the engines, and the central heating furnace. With the white paint of the boat deck, and the low height of the various exhausts, I saw no dark spots or soot up here, especially surprising since Mike had just returned from Florida. When I mentioned it to him, he commented that a well-maintained diesel doesn’t smoke, except occasionally during startup. (You guys who think all dry exhausts are smoky and sooty should see this boat—clear evidence that yet another so-called fact is perhaps just another myth.)
There are two watertight doors into the pilothouse, up a couple of steel steps from the deck. There used to be inside access from the pilothouse into the rest of the interior, but Mike has all but removed that access by putting a day head on the other side of the door. He doesn’t find it a problem.
This wheelhouse is all tug boat. Mike proudly told us that his lovely wood wheel came from the last steam-powered tug to operate in Baltimore Harbor. He ought to know, as he was the tug’s captain. All wiring and switches are mil-spec and completely overdone. The rest of the pilothouse reflects the control center of a working tug. Instrumentation consists of basic equipment, but it is all big, heavy, commercial gear.
The saloon was kept as a large living room, rather than sharing the available space with a galley as is sometimes done in T-boat conversions. It was a conscious decision, and Mike is glad to keep the saloon large and open. The room measures 9’6″ wide by 15′ long, and there is 6’1″ of headroom.
Two huge watertight doors allow entry from the side decks, and Mike’s construction team cut out all the portholes and replaced them with opening windows. The feeling is bright and open, with excellent visibility. While interior decorating remains unfinished, it is clear this will be a rather pleasant living room when completed. Real chairs, sectional sofabed, baseboard heating, Berber rugs, the works.
The forward section of the saloon includes a built-in wetbar, and to the left of the wetbar is a door into the day head and engine room. The opposite side of the bulkhead opens into a short corridor that goes down a flight of metal stairs into the hold, er, now master stateroom. There are three inches of insulation in the sides and roof of the saloon. Cozy.
The day head is located in a grate-floored compartment that sits overtop the engine room. The grates are removable for getting machinery in or out, and are commonplace onboard workboats. This compartment is sort of a mud room in its utility, a great place to keep lights, cords, electrical panels, paints, and other necessary but stored-away-somewhere items.
A metal ladder leads down from the grated floor, into the largest engine room we’ve seen to date. This Holy Place measures roughly 17′ by 17′, with 6 feet of headroom throughout. Talk about an engine room!
Centerline in the compartment are the side-by-side Detroit Diesel 6V71s, mounted together to a Falk marine transmission with Twin Disc clutches. Mike can run the boat on either engine or both engines; together they produce 500 horsepower. The Falk gears are designed to handle up to four separate engines driving a single shaft through 4:1 reduction gears, spinning the 48″ by 54″ four-blade propeller.
While four engines would still fit within the space left after removing the single Buda engine, Captain Effort just doesn’t see the need for all that extra horsepower. He normally runs the boat on one engine, and both engines only get used during tug operations. Under way at 8.6 knots on one engine running at 1,300 rpm (spinning the prop at 300 rpm), the fuel burn is 4.8 gallons per hour. That’s good efficiency indeed, and is an endorsement to the T-boat’s hull form.
(One interesting detail is that Mike originally had both engines share the common dry exhaust and keel cooling system. It worked great when both engines were running, but unfortunately, it didn’t work so well with just one engine. Seems the running engine would work to heat up the idle engine, instead of cooling itself off, so Mike had to change the exhaust and cooling circuits. Instead of ripping out a perfectly good dry exhaust system to install two new systems, he instead converted one of the engines to a wet exhaust system—much easier and less wasteful. This dual engine set up has an added bonus. When running the boat from the boat deck, Mike can run the boat with the wet exhaust-cooled engine, making it really quiet up on the boat deck.)
Along with the two diesel engines, there are two gensets. One is a ten kW Lister diesel genset that produces 220VAC. The second genset is a Hatz/Wisconsin single cylinder, air-cooled, hand crank-started diesel engine that drives both a 2 kW 110 VAC generator and a 32VDC alternator. These varied power sources serve all of the different onboard electrical needs. The ship’s battery bank consist of four 8V batteries (each with 250 Ah capacity), wired as a 32VDC system.
With the grand dimensions of this engine room, it’s easy to fit several large tool boxes, a workbench, drill press and grinder, and all sorts of fittings, tools, and parts in their own bins. There is even plenty of room to fit a full-size domestic oil furnace that provides hot water central heating throughout the boat. (Unfortunately, a recent puff-back in the system turned the once-pristine white engine room into a gray off-white.)
As far as tankage aboard MI-T-MO, there are two 500 gallon fuel tanks and a 150 gallon day tank for the gensets, for a total of 1,150-gallon fuel capacity. Two water tanks hold a total of 400 gallons.
Down the flight of stairs from the saloon brings you into the master stateroom. Taking advantage of the full 17′ by 17′ cargo hold area, Mike decided against converting this area into multiple yacht-sized staterooms, as he wanted a real home.
So instead of small bunks and so forth, this master stateroom has a queen-size bed, real furniture chests of drawers, a full domestic bathroom-sized head with full-size tub/shower, stacked full-size washer/dryer, built-in desk and entertainment center, and enough room left over for the visual open feeling of a true master bedroom.
What can I say…Mike and Ramona didn’t want to skimp on living space, and they’ve taken this to heart. After all, how often do guests stay aboard beyond the needs of a sofabed in the saloon? There are large opening portholes in this stateroom, and due to the construction of the cargo hold in this hull, headroom averages a full 7’4″.
Moving forward into the next area of the boat brings you into the galley and crew quarters. It was decided to keep the galley in its original location, although Mike told us other conversions have moved the galley up to the saloon level. But it works just fine right where it is, and the added fo’c’s’le hatch allows easy food transfer up to the deck where most meals are served, weather permitting. The refrigerator is located on the centerline, in the only square corner in the entire 65 feet of boat. Mike and Ramona updated the galley, of course, but kept the overall layout and some of the original furnishings.
Across from the galley are two single bunks, which don’t get used much, and a small guest head on the outboard side of the hull.
All things considered, the layout of MI-T-MO is centered around real living space rather than maximizing accommodations. Less is definitely more on this boat.
Compared to other T-boat conversions, the engine room space is intact (other have made it smaller to fit more staterooms), there is a big saloon (rather than a galley/saloon combo), and there is superior space for two people (rather than smaller but more numerous staterooms). If they did it over again, Mike told us he might move the queen bed into an island configuration, and perhaps rearrange some of the other details, but he is pretty happy with MI-T-MO just the way she is.